Plusmax The Guard


Product code: PLSMX-GUARD

Stock status. Shipping estimate from item in stock. Currently unavailable

1-3 workdays

Status: End of line

Condition: New

* Required Fields

The Guard is a removable chin-guard designed to upgrade your Plusmax Plus or PlusAir open-face helmet to full-face.

Removable Chin Guard for Plusmax PlusAir Helmets

This removable chin-guard has been designed to upgrade your Plusmax Plus or PlusAir helmet open-face helmet to full-face, to help protect you when partaking in extreme sport activities like paragliding, hang gliding, base jumping, big mountain ski and snowboarding. It is made from injected ABS which ensures lasting durability, and is available in various colour options.

All Plusmax Plus and PlusAir helmets can be upgraded with this removable chin-guard, which is backed up by the Plusmax Worldwide Lifetime Warranty.


  • ABS Technology
  • Plusmax safety design
  • Ventilation
  • Weight: 120g
  • Plusmax Worldwide Lifetime Warranty
  • One size fits all helmet sizes


  • Black*
  • White*
  • Electric Blue*
  • Green*
  • Grey*
  • Orange*
  • Red*
  • Carbon (X-Alps limited edition).

*Finish: Soft Touch coated

Chinguard Fitting Instructions

IMPORTANT! Fitting the chinguard takes time, care and patience. It's a 10 minute job, not a 2 minute job!

Download Removable Chin Guard Assembly as a PDF file


Step 1.

Ear pads should be removed before fitting the chinguard. Un-do both poppers and slide the ear pad out from between the helmet shell and liner. You can re-fit the ear pads afterwards, but the helmet is certified either way, so try the helmet before you re-fit them as you may prefer the extra space around your ear.


Step 2.

Next remove the self adhesive carbon-look stickers above the ear pad, on the outside of the helmet shell. These will not be used again so you can discard them. Removing the sticker reveals 2 mounting holes on each side of the helmet.

Step 3.

Fit one silver coloured round alloy nut into the rear of each of these holes, ie from the inside of the helmet shell, next to the helmet lining. You'll need to squeeze these nuts into the hole, they are tight and designed to self lock once fitted. This bit is quite a fiddle, and you may want to use the end of a flat bladed screwdriver or similar to press them home.

If the hole is very tight and you cannot get the alloy nut to press home, use the following procedure: Without fitting the chinguard, hold the alloy nut flat against the hole as above, and enter a black Allen (hexagonal) head bolt from the outer side of the helmet. Being very careful not to cross thread the nut, slowly tighten the black Allen bolt with the Allen key spanner provided. Make sure you keep the nut and bolt perpendicular to the helmet. Gently tightening the bolt will draw the silver coloured alloy nut into the hole, and it will become captive. Keep a careful eye on the nut and bolt as you tighten, and don't screw too tight or too far, you only need to pull the nut far enough into the plastic to keep it there for now; full tightening will be achieved when you fit the chinguard. Once the silver coloured alloy nut is captive, carefully unscrew the black Allen bolt. Repeat this procedure on all four holes. You should end up with all four silver coloured round alloy nuts captive in the helmet shell.

Step 4.

Carefully fit the chinguard to the helmet, ensuring the webbing chin straps stay on the inside of the helmet.


Step 5.

Now re-fit the 4 black Allen bolts one by one, tightening them by finger to begin with, and again being very careful not to cross thread the nut. Then using the Allen key spanner tighten the bolts carefully, and NOT TOO TIGHT! You need them to be tight enough so as not to come undone, but not so tight that they start to press into the plastic of the chinguard.


Step 6.

You can now re-fit the ear pads if required, by sliding them carefully back between the helmet shell and liner. Make sure they are lined up correctly, and close the poppers on the webbing chin strap. You're finished!

We hope the above all makes sense! If you have any questions or want any advice then Contact Us


Additional Information

Condition New
Shipping Details 1-3 workdays
Model Status End of line

Only registered users can write reviews. Please, log in or register